Cables
Generic Cable
CY-CBL-6P-EXT50, CY-CBL-6P-EXT100, CY-CBL-6P-EXT300, CY-CBL-6P-EXT500
CY-CI0/CY-RIO extension cable.
This cable extends the connection between CY-CI0/CY-RIO and camera and is universal for all camera.
CY-CBL-6P-FAN
CY-CI0/CY-RIO generic fan-out adapter cable.
NB: Don't mix GND and shield! The shield is connected to a slightly thicker black wire than the GND black wire. These are the signal from the controller side. Connect the TX to the camera RX and vice versa.
CY-CBL-6P-PFAN
CY-CI0/CY-RIO generic power and fan-out adapter cable.
Cable for equipment with 12v 5.5x2.1 mm power jack.
- Marshall mini camera
- PTZ RS232/422 camera
- Pan/Tilt heads
CY-CBL-6P-ST-15, CY-CBL-6P-ST-50
CY-CI0/CY-RIO adapter cable with straight mapping.
Cable suitable for the CY-RSBM module.
CY-CBL-6P-PWR
CY-CI0/CY-RIO power cable for low consumption Devices
Use for Tally LED for instance (see LED Assembly Guide).
CY-CBL-DTAP
Power supply cable for CY-CI0/CY-RIO from battery or camera using DTAP connector.
AJA Cable
CY-CBL-6P-AJA-01
CY-CI0/CY-RIO adapter cable AJA Rovocam.
The AJA Rovocam is controlled over RS232 directly at the back of the camera or at the RovoRx units.
Astro Design Cable
CY-CBL-ASTRO-01
CI0/RIO cable for Astro Design 8K camera.
Bradley Cable
CY-CBL-6P-BRADLEY-01
Adapter cable provides power and control to the Bradley Micro L PAN/TILT head. You need a separate cable to connect to your camera (see Marshall and Dreamchip)
Canon Cable
If you don't know, it means you need this: CY-CBL-6P-B4-01
CY-CBL-6P-B4-01 (default)
This cable is used to connect the CY-CI0/CY-RIO to the Canon B4 or Cine Servo lenses.
CY-CBL-6P-CN-REM (advanced robotic)
CIS Cable
CY-CBL-6P-CIS-01
CY-CI0/CY-RIO adapter cable for CIS camera.
Cable for CIS camera with a HR10A connector for power and TRRS audio socket for control:
- VCC-HD3
- VCC-HD10ZM
CY-CBL-6P-CIS-02
CY-CI0/CY-RIO adapter cable for CIS and Camera Corps.
This cable provides power and control to the mini-camera from CIS and Camera Corp using a HR10A connector.
DJI Cable
CY-CBL-6P-SBUS-01
DIY Cable
The connector is difficult to find. We recommend you build your own cable with a 2.54mm pitch socket header and a CY-CBL-6P-FAN cable.
Dreamchip Cable
CY-CBL-DREAMCHIP-03 (default)
CY-CI0/CY-RIO adapter cable for Dreamchip camera.
This cable provides power and control to all Dreamchip Mini Camera.
There are multiple revisions of the Dreamchip cable: CY-CBL-DREAMCHIP-01 and CY-CBL-DREAMCHIP-03.
Both revisions are compatible, but only CY-CBL-DREAMCHIP-03 is currently sold.
CY-CBL-DREAMCHIP-02 (SSM500 & Atom Two)
CY-CI0/CY-RIO adapter cable for Dreamchip DCT-Powercable 350-00011v.
This cable provides RS485 control on all Dreamchip camera with the Dreamchip DCT-Powercable 350-00011v.
Fujinon Cable
If you don't know, it means you need this: CY-CBL-6P-FUJI-02 (+ CY-CBL-6P-B4-01)
CY-CBL-6P-FUJI-01 (discontinued)
Discontinued to to bug in lens when used with handels. Requires a lens firmware upgrade.
CY-CBL-6P-FUJI-02 (default)
Use this cable for all Fujinon lenses (B4 and Cabrio), in conjonction with this cable: CY-CBL-6P-B4-01
CY-CBL-6P-FUJI-03 (advanced robotic)
This cable
- Camera keeps iris control (directly connected to the camera)
- CI0/RIO takes control of zoom/focus
- You can get iris/zoom/focus from the RCP
Ikegami
DIY Cable
The connector is pricey and difficult to find. We recommend you build your own cable.
This adapter cable provides power and control over Ikegami professional cameras through the 8 pins remote interface.
This cable has to be built from a Cyanview multipurpose CY-CBL-6P-FAN cable and a Tajimi Male Plug 8 pins PRC05-PB8M connector.
Refer to Pin Assignment table in the document below for cable soldering.
IOI Cable
CY-CBL-6P-IOI-01
CY-CI0/CY-RIO adapter cable for IOI camera.
This cable provides power and control to all IO Industries camera.
LANC Cable
CY-CBL-6P-LANC-03
CY-CI0/CY-RIO adapter cable for LANC controlled cameras or Canon Remote-A port.
This cable provides control over compatible with Sony LANC physical interface:
- Sony, JVC
- All Canon camcorders and cameras
- Blackmagic LANC interface
CY-CBL-6P-LANC-01 (Canon Remote-A) (discontinued)
CY-CI0/CY-RIO adapter cable for LANC camera.
This cable provides control over compatible with Sony LANC physical interface:
- Sony, JVC
- All Canon camcorders and cameras
- Blackmagic LANC interface
The second port is not used
CY-CBL-6P-LANC-02 (Sony LANC) (discontinued)
CY-CI0/CY-RIO LANC adapter for Sony LANC cameras with control pass-through.
With double LANC ports: LANC input for remote control pass-through, camera LANC output. The second port is not used to control a second camera but to connect the zoom/focus handle of a camera like Sony PXW-FS7 which only has a single LANC port. Later cameras like the Sony ILME-FX6 and later have dual LANC ports or the zoom handle connects using other types of connectors so this cable is not necessary anymore.
Marshall Cable
CY-CBL-6P-MARS-02 (new)
CY-CI0/CY-RIO adapter cable for Marshall camera.
This cable provides power and control to a newer Marshall mini camera having 12 pin Hirose connector.
There are multiple revisions of the Marshall cable: CY-CBL-6P-MARS-01 and CY-CBL-6P-MARS-02.
Both revisions are compatible, but only CY-CBL-6P-MARS-02 is currently sold.
CY-CBL-6P-PFAN (older)
CY-CI0/CY-RIO adapter cable for Marshall camera with power and RS485 Phoenix.
Cable for Marshall mini camera equipped with power DC jack and 2 position RS485 terminal block.
Panasonic
CY-CBL-6P-PAN-10P
CY-CI0/CY-RIO adapter cable for Panasonic camera.
This cable provides control over the older Panasonic P2 camera.
Sony
CY-CBL-SONY-8P-03 700 Legacy
CY-CI0/CY-RIO adapter cable for Sony Legacy 8-pin remote interface with power.
This cable provides control to Sony professional camera and camcorder through the 8-pin remote interface.
There are multiple revisions of the Sony cable: CY-CBL-6P-SONY-8-01, CY-CBL-6P-SONY-8-02, and CY-CBL-6P-SONY-8-03.
All revisions are compatible, but only CY-CBL-6P-SONY-8-03 is currently sold.
The actual cable with order reference CY-CBL-SONY-8P-03 is labelled CY-CBL-6P-SONY-8-03.
Tilta
If you don't know : If you don't know, it means you need this: CY-CBL-TILTA-SERIAL.
Lockable, works with CI0/RIO and provide power+control.
CY-CBL-TILTA-USB
CY-RIO adapter cable for Tilta motors.
Plugs on CY-RIO (USB) and Tilta motors (LEMO). Needs external power supply.
CY-CBL-TILTA-SERIAL
CY-RIO/CY-CI0 adapter cable for Tilta motors.
Toshiba Cable
CY-CBL-6P-TOSHIBA-01
CY-CI0/CY-RIO adapter cable for Toshiba camera.
Cable for Toshiba camera and any RS232 device.
VISCA Cable
CY-CBL-6P-PFAN → VISCA4, VISCA5, VISCA9
CY-CI0/CY-RIO adapter cable with power for VISCA camera using RS422 can be constructed from CY-CBL-6P-PFAN and a 4, 5 or 9 pin 3.5 mm pitch Phoenix connector.
